OPEN 9:00 to 5:00 PM EST (Mon-Fri)

Racetronix 255LPH F98 Fuel Pump Kit HP 1998 RXP255 for 1998 LS1 Camaro, Firebird, Trans Am
  • SKU: 672-RFPK-002

Racetronix 255LPH F98 Fuel Pump Kit HP 1998 RXP255 for 1998 LS1 Camaro, Firebird, Trans Am

Shipping calculated at checkout.

Fuel Pump Module

  • Racetronix 255LPH turbine fuel pump with reduced noise and enhanced reliability with E-85 enahnced fuels*
  • Anodized T6 aluminum fuel pump module for simple drop-in installation
  • Plug & Play heavy-duty in-tank Teflon wiring harness
  • All components come pre-assembled
  • Stainless steel hardware
  • Installation hardware & instructions included


The FPA-002A incorporates our new RXP Turbine-Tech fuel pump which supplies 225LPH of fuel @ 58.0PSI @ 13.5V*. Racetronix RXP pumps use new turbine technology to reduce pump noise, improve reliability and provide enhanced compatibility with Ethanol enhanced fuels. The FPA-002A pump and FPWH-002 harness are recommended for factory HP upgrades to 600HP @ 58PSI using the factory lines and fuel pressure regulator. HP support may vary based on motor B.S.F.C. and maximum fuel pressure (i.e. F/I motors). Please factor in a 20-25% safety margin between what your motor needs and what your fuel system can supply.

Our FPWH-002 harness included in this kit is required for a HP pump to meet stated performance specifications because the factory wiring was not designed to handle high-performance pumps which draw more than twice the power of a factory pump. A performance reduction of 15-25% in pump performance can be expected along with reduced reliability when a HP pump is run off of the factory wiring harness.

The FPA-002 incorporates a high-performance 255LPH pump but since this pump is run at a base pressure of 58PSI (vs. 43.5PSI) its flow rating drops to a nominal 225LPH @ 13.5V. This has been a constant source of confusion on car forums due to misinformation being posted.

Please contact your local Racetronix dealer to discuss your fuel requirements.

The Racetronix LS1 fuel pump module is a direct drop-in replacement for the factory GM plastic pump assembly. No modification is required to the factory sending unit. Simply remove the old plastic pump assembly and put in the new one. Installation of the Racetronix LS1 fuel pump module can be easily done in under 5 minutes with basic hand tools. The Racetronix fuel pump module is designed to position the pump in the factory location for optimal performance. Should the pump ever require service, it can be removed from the module using the supplied hex key by removing two of the mounting dowels. The Racetronix pickup adapter allows the factory filter sock used on the Walbro pump which has a much greater surface area than the after market types thereby providing longer filter service life. Retaining the factory filter sock also allows the GM return system be kept intact thereby reducing contamination and foaming. The Racetronix LS1 fuel module is made from T6 high-grade aluminum which is bright dip anodized and sealed for long life. A factory-type fuel feed tube is clamped to the pump's outlet for added reliability under high operating pressures. This fuel tube is more flexible than a rubber line making for easier installation. The fuel tube is highly resistant to the harsh chemicals in today's gasoline which tend to attack and dry out rubber fuel lines. The Racetronix in-tank pump wiring eliminates the need for an in-tank wiring adapter or butt connectors which can be unreliable and can cause voltage drop. The Racetronix in-tank pump harness plugs directly into the pump and the other end into the factory bulkhead connector. Teflon wire is used throughout as is done from the factory. Teflon wire is the most resistant to gasoline and provides maximum voltage to the pump.

Why use a Racetronix Fuel Pump Upgrade Harness?
Alternator-direct power for maximum power!

  • Compatible with factory terminals and connectors (no cutting or splicing required)
  • Weatherproof connectors
  • Heavy-duty automotive-grade copper wire
  • Heavy-duty weatherproof relay
  • Weatherproof fuse holder
  • Alternator-direct power for maximum pump performance
  • Silicon grease, spare fuse, wire ties included
  • Stainless steel mounting hardware
  • Compatible with various pump boosters (i.e. KB, MSD) (optional)


High performance fuel pumps need a good power source in order to perform to their full potential. On average a Walbro high-performance fuel pump requires twice as much power as a factory fuel pump. Factory wiring is just enough for a factory pumps power requirements because manufacturers need to save cost and weight. Racetronix field tests have shown that running a high-performance fuel pump off of the factory wiring can cut pump performance by 30% or more. Problems with failing factory relays, connectors/terminals and fuse contacts are also common when excessive load is placed on them.

The Racetronix plug and play harness is designed to remove all fuel pump load from the factory pump circuits while providing the pump with a new heavy-duty power source. The Racetronix harness gets its power directly from the alternator's battery terminal. The voltage at the alternators output is typically 1-2 volts higher than at the battery when the motor is running (high charge/load conditions and WOT). This means that your high-performance pump can provide as much as 20% more fuel in some cases. The Racetronix harness uses high-quality automotive-grade wire which is resistant to oil, gas, heat and rot. The main length of wire in the Racetronix harness is three to four gauges thicker than factory wire which helps reduce resistive power loss to almost non-existent levels. This helps improve pump performance by as much as another 10-20%. High-quality weatherproof fuse holders and relays are used for maximum reliability. The Racetronix harness has factory-type connectors which plug directly into your fuel pump module/sender so no cutting or splicing is required. The Racetronix harness has a redundant ground upgrade as it is necessary to improve the harness on the negative side of the pump's supply as well.

There is nothing worse than being in the middle of an installation only to find that the manufacturer has skimped on installation hardware. This is why Racetronix supplies a spare ATM fuse, 25 black nylon wire ties, silicon grease and stainless mounting hardware with each kit.

Racetronix harnesses are considered the best by which all others are judged. Attention to detail in every Racetronix harness is evident at first glance. Racetronix spares no expense to ensure reliability, ease of installation and performance.  All Racetronix harnesses are assembled using our computerized crimp-quality monitoring system and then circuit checked for the utmost in reliability. This harness is backed by our limited lifetime warranty.


An optional battery to body ground upgrade kit is available. This kit upgrades the under-rated factory ground wire running from the battery to chassis. It includes a flexible 8 gauge copper wire and battery nuts with accessory taps. We highly recommend this inexpensive option because this is a weak point in these cars.

The Racetronix harness comes equipped with an interface connector just after the relay (see product picture above). This connector in combination with an optionally supplied connector set allows for easy plug and play addition of a pump booster / voltage amplifier such as the MSD or KB units. These voltage amplifiers / boosters will allow the Racetronix single in-tank pump system to support an additional 100-200 flywheel HP (B.S.F.C. dependant) when run at 16-17 volts. This configuration offloads the excessive current draw placed on the factory wiring onto the heavy gauge Racetronix harness system. System diagnosis becomes easier by simply being able to unplug, isolate and bypass sections of the wiring system.

Contact Us Now to Speak with one of our Professionals in High Performance!
PHONE: (586) 294-4404
FACEBOOK: @FullThrottleSpeed
E-MAIL: steve@fullthrottlespeed.com